Digital DEClaser 3500 Guia de Instalação

DEClaser 1100 PrinterInstallation GuideOrder Number EK–DCL11–IN–002Digital Equipment CorporationMaynard, Massachusetts

Human Services (DHHS) Radiation Performance Standard according to theRadiation Control for Health and Safety Act of 1968. The printer does notemit haz

Chapter 1Preparing Your SiteElectrical and environmental conditions surrounding the work location canaffect the performance of the DEClaser 1100 print

1.2 Operating Location RequirementsInstall the DEClaser 1100 printer in an area that meets the followingrequirements:• A flat, level surface free from

The following figure illustrates the space requirements for the printer whenthe optional printer feeder unit is installed.mlo-0058071.3 Environmental C

Chapter 2Unpacking Your PrinterThis chapter explains how to unpack the DEClaser 1100 printer andidentifies printer components.CAUTION: Do not power on

The following illustrations show the correct and incorrect methods of liftingthe printer.CAUTION: When moving the printer from one location to another

Never lift the printer by the paper output tray slot.mlo-005803Unpacking Your Printer 2–3

2.2 DEClaser 1100 Printer ComponentsThe following illustration shows the front view of the printer with the majorcomponents identified.mlo-0058252–4 In

Number Description1 Control panel2 Top output tray3 Paper stop4 Font cartridge slots5 Power switch6 Front cover release button7 Paper tray8 Extension

The following illustration shows the rear view of the printer with the majorcomponents identified.mlo-005823Number Description1 Air vent2 Power cord re

First Printing, January 1991Revised, June 1991The information in this document is subject to change without notice and should not beconstrued as a com

2.3 Removing the Shipping MaterialRemove all shipping and packing material using the following procedure.1. Remove the printer from the plastic bag.2.

3. Open the paper tray by pulling it toward you.mlo-0058242–8 Installation Guide

4. Lift up the release button to open the front cover.mlo-005808Unpacking Your Printer 2–9

5. Remove the orange-colored packing stopper by squeezing and thenlifting it out.Discard the packing stopper.mlo-006612B6. Continue with Chapter 3 to

Chapter 3Installing the EP-L CartridgeThis chapter describes how to install the EP-L cartridge.When handling the EP-L cartridge, be sure you:• Install

1. Remove the EP-L cartridge from its shipping carton.mlo-0058093–2 Installation Guide

2. Remove the EP-L cartridge from its protective bag.mlo-005810Installing the EP-L Cartridge 3–3

3. Hold the cartridge as shown and gently rock it five or six times todistribute the toner evenly.NOTE: Do not shake the cartridge vigorously.mlo-00581

4. Remove the sealing tape from the cartridge by holding the cartridge ona flat, stable surface and gently pulling the orange tab straight out ofthe ca

5. Insert the EP-L cartridge by aligning the arrow on the cartridge withthe mark on the printer, and gently push the cartridge in until itstops.mlo-00

First Printing, January 1991Revised, June 1991The information in this document is subject to change without notice and should not beconstrued as a com

6. Slowly close the front cover.NOTE: If the EP-L cartridge is not pushed in completely, the front coverwill not close.mlo-005814Installing the EP-L C

Chapter 4Connecting the PrinterYour printer is equipped with the following interface connectors:• Serial• Parallel• VideoThis chapter explains how to

4.1 Serial Interface ConnectionThe serial interface connection uses the supplied BC16E serial interfacecable and the H8571–E serial interface adapter.

2. Plug one end of the BC16E serial interface cable into the H8571–Eserial interface adapter.mlo-0058193. Plug the other end of the BC16E serial inter

4.2 Parallel Interface ConnectionThis procedure uses an optional BC19M–10 parallel interface cable todescribe the parallel connection to the printer.

4.3 Power Source ConnectionUse the following procedure to connect the printer to the wall outlet.1. Make sure the printer power switch is in the OFF (

2. Plug the power cord into the power cord receptacle.mlo-0057203. Insert the other end of the power cord into the wall outlet.WARNING: Do not use a g

Chapter 5Loading PaperThis chapter explains how to load paper into the paper tray and how toprint the printer’s default data sheet. The paper tray hol

5.1 Loading PaperThe following instructions show how to load paper.1. Pull the extension tray straight out.MLO-0058155–2 Installation Guide

2. Tap a stack of paper on a flat surface to align the edges.MLO-005816Loading Paper 5–3

FCC NOTICE: This equipment generates and uses radio frequency energyand if not installed and used properly, that is, in strict accordance with themanu

3. Insert the stack of paper into the tray as far as it will go.The right edge of the paper should be touching the paper feed guide.Forms and letterhe

4. Slide the adjustable paper feed guide to the right (if necessary) until itjust touches the paper stack.Do not press the adjustable paper guide agai

5.2 Turning the Printer Power OnThe following instructions show how to turn the printer power on.1. Press the power switch to the ON ( |) position.2.

mlo-0058215.4 ConclusionThis concludes the installation of your DEClaser 1100 printer. Refer toyour DEClaser 1100 Printer Operator’s Guide for detaile

Appendix ACabling InformationThis appendix describes the different cable combinations to use forconnecting your printer to a host device and includes

Table A–1 (Cont.): Cables and Adapters for CommunicationConnectionsConnector TypeAdapter and CableRequiredConnectingInstructions9-Pin Plug Hosts (DEC)

Table A–1 (Cont.): Cables and Adapters for CommunicationConnectionsConnector TypeAdapter and CableRequiredConnectingInstructions9-Pin Plug Hosts(IBM P

Table A–1 (Cont.): Cables and Adapters for CommunicationConnectionsConnector TypeAdapter and CableRequiredConnectingInstructionsEuropean DECstationsPa

A.2 Interface Programming InstructionsThis section describes how to set up an IBM PC to interface with yourprinter.A.2.1 Serial Flow ControlIf you are

If you are using a 25-pin PC/SA with xon/xoff, follow these steps:1. Edit your AUTOEXEC.BAT file to contain the following two lines:mode com1:4800,n,8,

ContentsPreface vChapter 1 Preparing Your Site1.1 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–11.2 Operating Lo

Appendix A Cabling InformationA.1 Cable Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–1A.2 Interface Programming Inst

PrefaceThe DEClaser 1100 printer is a nonimpact, desktop, page printer. Thisguide covers the installation of the DEClaser 1100 printer up to the point

Ordering Additional Copies of This Documentation SetThe documentation set consists of one of each of the following:• DEClaser 1100 Printer Installatio

ConventionsThe following conventions are used in this guide:Convention MeaningNOTE Notes provide important additional information.CAUTION Cautions pro